Article by-Lehman Mcfadden

When you hire a plumber, it can cost a lot of money for even a very simple repair that you could have done yourself with some basic plumbing knowledge. Don't waste money on professional plumbers again! Read on for some tips on solving your own plumbing problems with tools you have at home.

Ensure that everyone in your household knows how to turn off the main water supply, or knows how to contact someone who can. In the event of a burst pipe or other water-related emergency, you should immediately turn off the water to prevent flooding, structural damage, and a sky-high water bill.

Check the filters in your furnace, regularly. If these filters have not been cleaned or replaced recently, they may become clogged. This will affect how well your furnace is able to work, meaning that you may not have enough heat during the winter. Take this simple step, as soon as the weather starts to become cold.

Do not let your faucet leak. Did you know a leaky faucet can waste about 150 gallons of water every day? If you have a leak, never ignore it. It could be coming from the faucet or the pipes. Continually check pipes and faucets for extra moisture or small leaks.

If your water pipe has frozen, start water running in the faucet closest to the frozen pipe. This will give excess water somewhere to drain as the ice in the pipe thaws. Letting the water drain out will relieve pressure in the frozen pipe, which will reduce the chances of it bursting and damaging your home.

Drain the sediment from the bottom of your hot water heater twice a year to keep the hot water heater working at its optimal levels. Simply open the drain valve and allow the water to run out into a bucket until the water runs clear. Then close the drain valve.

To be successful in any plumbing project, make sure you turn the water off before you start unscrewing pipes. This tip might actually sound insulting, but you are probably getting caught up in having the right tools and parts and being dressed right. Double check that there is not a splash waiting for you. Then triple and quadruple check.

There are two ways to remove stubborn clean-out plugs. Try to use a hammer and chisel to loosen it. The only other option is to chisel right through the clean out plug.

When plunging a drain to attempt to remove a blockage, first make sure that the drain is completely covered in water. This helps to form a seal. Then, plunge at least fifteen to twenty times before stopping. Repeat the process two to three times. If this doesn't work, try a chemical drain cleaner.





When you wash your hands, be sure that you have not left any soap on the faucet handles. What people do not know is that leaving soap on these fixtures can cause fixtures to corrode. Just take two seconds after you are done washing your hands to remove excess soap from the handles.

In order to get the most efficiency from your hot water heater, it's important to learn what size tank your household actually needs. If you know how many people are in the home and how many appliances use hot water, you will have a good idea of what size tank is appropriate.

A great way to save a few dollars is to add insulation to your hot water heater. Much of the energy required to heat the water in your home is the expense from keeping the water in the tank hot for when it is needed. Adding an extra layer of insulation can help reduce this cost.

Have you tried patching your pipe with the store-bought patching kits only to have that section of your plumbing continue leaking? Replacing browse around this site damaged pipe is a more permanent solution than patching. First, you must shut off the main water valve, and drain the water from the damaged section. Cut out the damaged section of the copper pipe, leaving about an inch of extra pipe on both sides of the damaged area. Remove corrosion from inside the pipes with a wire brush. Apply flux to the replacement pipe and the remaining pipe. Slide the piece of replacement pipe into place with couplings. Apply solder all around the joint, and use a propane torch to solder the replacement section into place.

If you own property where the temperature gets below freezing for an extended amount of time each year, you should make sure that pipes located in unheated areas, such as crawl spaces and garages, are insulated. Pipes that are exposed to the outside elements or those that are prone to freezing, should be protected by heat tape or thermostat-controlled heat cables to prevent them from freezing.

Clean washing machine lint traps and use pantyhose over the water outlet tube to prevent lint, fuzz and other debris from clogging sewer or septic system filters. Fine mesh traps are also available for this purpose, but a package of knee-high nylon stockings and plastic ties can provide enough filters to encourage you to do the job regularly.

Mold growing at the base of your toilet can indicate that condensation is forming on your toilet bowl thanks to room temperature versus bowl and water temperature, or that you have a leak in the wax seal around your toilet. To replace the wax seal, turn off the water to the toilet, disconnect from the water supply and then lift the toilet and replace the ring. The real trick is setting the toilet back down on the ring correctly. Buy an extra ring in case you mess up and to avoid having to run to the hardware store in the middle of the job.

When facing temperatures below freezing in the winter it is important to leave the hot water dripping. This makes sure that the pipes don't freeze over and saves you the expensive repair of fixing and or entirely replacing a broken pipe. The slight cost of dripping hot water is well worth saving you from that large expense of replacing a broken pipe.

If you have chrome or ceramic plumbing fixtures, be very careful when making any types of repairs. These types of finishes are very easily scratched, and they are expensive to get fixed. Be careful and exercise caution when dealing with these finishes. Consider if it may be better to hire a professional.

If you are remodeling your house, take pictures of the inside of your walls, ceilings and floors. You will be able to have a clear idea of where your pipes are located in case you need to do maintenance later. You should also consult your pictures if you want to drill holes in your walls.

Source Webpage should have given you some much needed insight on where to start and how to begin with your own plumbing jobs at home. These tips were thoughtfully compiled to help the plumbing beginner learn the basics and some other cool techniques that are simple enough to use for everyday maintenance and repair.